[Oct 08, 2022] Get Up-To-Date Real Exam Questions for NACE-CIP2-001 with New Materials
Updated NACE-CIP2-001 Certification Exam Sample Questions
NEW QUESTION 10
In the event of a conflict between the Product Data Sheet and the Specification:
- A. The Product Data Sheet prevails
- B. It is up to the Inspector to decide which one to follow
- C. The Specification prevails
- D. It is up to the Applicator to decide which one to follow
Answer: C
NEW QUESTION 11
In which type of concrete are laitance commonly encountered?
- A. Gunite
- B. Concrete block (poured with a form)
- C. Poured (wet cast)
- D. Glass fiber cement
Answer: C
NEW QUESTION 12
Ideally, documentation requirements should be defined:
- A. At the pre-job conference
- B. In the specification
- C. By the contractor
- D. By the inspector
Answer: B
NEW QUESTION 13
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - Cross Hatch
- B. Method B - X cut
- C. Method A - Cross Hatch
- D. Method A - X Cut
Answer: D
NEW QUESTION 14
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
Answer: A
NEW QUESTION 15
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings protect the contents and the container.
- B. coatings are expected to degrade over time.
- C. linings are more durable than coatings.
- D. coatings are more durable than linings.
Answer: A
NEW QUESTION 16
When conducting inspections the Inspector should follow which standards:
- A. The specified standards
- B. NACE and SSPC standards in North America
- C. Australian standards in Australia
- D. ISO standards in Europe and Asia
Answer: A
NEW QUESTION 17
Thermal Spray coatings provide:
- A. Inhibitive protection
- B. Sacrificial protection
- C. Thermal protection
- D. Barrier protection
Answer: B
NEW QUESTION 18
NACE Standards include:
- A. Standard Practices
- B. a) & b)
- C. Material Requirements
- D. a) only
Answer: B
NEW QUESTION 19
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A hardness tester
- B. A destructive paint inspection Tooke gauge
- C. A set of 14 pencils of varying hardness
- D. A mechanical adhesion tester
Answer: B
NEW QUESTION 20
Linings are used on the interior of pipelines to
- A. provide protection against soil chemicals.
- B. afford limited temperature insulation.
- C. protect the transported product.
- D. reduce magnetic polarity.
Answer: C
NEW QUESTION 21
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Challenge the supervisor's authority
- B. Express a willingness to work with the site team and follow the specification
- C. Defend the previous inspector
- D. Suggest to the Owner that the supervisor should be removed from site
Answer: B
NEW QUESTION 22
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Magnetic Gauge
- B. Ultra Sonic DFT Gauge
- C. Tooke Gauge
- D. Eddy Current Gauge
Answer: C
NEW QUESTION 23
Inspection and Test Plans are provided to:
- A. To supersede the requirements of the product data sheets
- B. So the Inspector doesn't have to read the entire specification
- C. So the contractor has a single document to reference
- D. Outline the inspection steps, sequencing and pass/fail criteria
Answer: D
NEW QUESTION 24
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise your QC Manager to change the ITP to the use of the salt smart meter
- B. Redo the pre-cleaning based on the other inspectors results
- C. Review the specification with the other inspector to see what method was specified
- D. Advise the other inspector he is using an incorrect method
Answer: C
NEW QUESTION 25
Dehumidification is defined as the removal of moisture vapor from the air to
- A. lower its dew point,
- B. provide worker comfort.
- C. raise its relative humidity.
- D. lower its temperature
Answer: A
NEW QUESTION 26
Which is used to calibrate a pH meter?
- A. Standard solvent solution
- B. Standard buffer solution
- C. Deionized water
- D. Distilled water
Answer: B
NEW QUESTION 27
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. The same as air blast cleaning
- B. Different than air blast cleaning
- C. Comparable to air blast cleaning
- D. Slightly different to air blast cleaning
Answer: A
NEW QUESTION 28
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cohesion failure
- B. Cold flow or creep
- C. Glue failure
- D. Adhesion failure
Answer: B
NEW QUESTION 29
......
NACE-CIP2-001 Study Guide Cover to Cover as Literally: https://passleader.passsureexam.com/NACE-CIP2-001-pass4sure-exam-dumps.html